← All projects

District Cooling · 2025

Chilled Water Distribution Network — Stress Analysis & Support Design, Kuwait

International design consortium, for a public university client

Project overview

Project details

Client
International design consortium, for a public university client
Year
2025
Category
District Cooling
Location
Kuwait (health sciences campus)
  • ASME B31.1
  • AISC 360-16
  • ACI 318-14
  • CAESAR II
  • SAP2000
  • IDEA StatiCa
  • Support Design
  • Closed Loop

Final design of a DN 900 closed-loop chilled water network at a health sciences campus in Kuwait. The scope covers CAESAR II stress analysis, support and base connection design, marked-up layouts and construction drafting.

  • DN 900closed-loop network
  • 77.0%governing expansion, of allowable
  • 14added anchors

The challenge

  • The package was inherited mid-stream with the original client submission date unchanged.
  • The DN 900 supply and return loop was already built, so the route was frozen: no re-routing, no added expansion loops and no meaningful geometry change.
  • A 4.5 °C supply line installed against a 45 °C ambient gives a 40.5 °C contraction, and a closed loop of this size has no free end to absorb it.
  • Every fix had to fit the as-built envelope, using bellows, anchors and support detailing only.

Our approach

  • The entire loop was modelled as one continuous CAESAR II system, so closure and load paths were solved once instead of being assumed at artificial boundaries.
  • Sliding restraints were modelled as unrestrained with steel-on-steel friction at μ = 0.30, conservative for anchor loads and realistic for movement.
  • Eight load cases: hydrotest, operating at design and operating pressure, matching sustained pairs, and three expansion combinations including the supply-to-return differential.
  • Two untied expansion joints, one per line, relieve axial force. Each has an axial stiffness of 7,700 N/cm, a transverse stiffness of 11,450 N/cm, an angular stiffness of 15,510 N·m/deg and an effective diameter of 955.7 mm.
  • Fourteen additional anchors divide the loop into controlled thermal blocks and stop movement from propagating around the ring.
  • Revised loads were fed back and every support type was re-verified. Support and anchor reactions were grouped into ten standard support types.
  • SAP2000 frame models designed the steel supports to AISC 360-16. IDEA StatiCa Connection models checked base plates, welds, cast-in anchors, concrete blocks and bearing to ACI 318-14.
  • Marked-up plan drawings show node numbers, support type callouts, anchor locations, expansion joint positions, tie-in points and contractor scope limits.

The outcome

  • Code compliance. Qualified in full against ASME B31.1 with no violations.
  • Expansion. The governing case reached 77.0% of allowable, under the 90% ceiling. The second expansion case reached 75.1% and the differential case 11.2%.
  • Sustained and hydrotest. Sustained stress peaked at 49.6% at design pressure and 41.4% at operating pressure. Hydrotest reached 24.3%.
  • Movement. Thermal excursions of about 147 mm horizontally and 30 mm vertically were absorbed by the bellows-and-anchor arrangement instead of the pipe. Sustained sag was 7.3 mm.
  • Supports. All support types passed structurally, with an AISC 360-16 P-M interaction peak of 0.82. Base connections reached 89.0% for anchors, 85.0% for welds and 33.4% for concrete blocks, with plate plastic strain of 1.2% against a 5% limit.
  • Reactions. Peak design reactions per support point were 397 kN vertical, 112 kN axial and 95 kN lateral. The governing anchor carried 973 kN axial and 356 kN moment.
  • Delivery. The complete package (analysis, support designs, base connections, markups and drafting) was issued within the client's specified duration, covering the gap left by a departing subcontractor and holding the design submission date.

Codes, standards and tools

  • ASME B31.1 (2020)
  • AISC 360-16
  • AISC LRFD 2016
  • ACI 318-14 Chapter 17
  • UBC 97
  • CAESAR II v13
  • SAP2000 v20.1
  • IDEA StatiCa Connection
  • AutoCAD

Discuss a similar project.

Get a quote