Project overview
Project details
- Client
- Engineering consultant, for a marine terminal owner/operator
- Year
- 2025
- Category
- Oil & Gas
- Location
- Gulf of Suez, Egypt
- ASME B31.4
- ASME B31.3
- API RP 1102
- API 5L
- CAESAR II
- Pipeline FEED
- HDD Crossing
- Sour Service
Front-end engineering design (FEED) of an 18-inch buried sour crude export pipeline linking a new multipurpose marine terminal to the existing national 30-inch crude grid. The scope covers route selection, wall thickness, material grade, crossings, pig-trap stations and issued alignment sheets.
- 18 inburied sour crude line
- ~2,075 madopted alignment with four crossings
- 97.3%governing utilisation
The challenge
- The corridor was tight. About 2 km of the route runs inside an operating port and across a public road network.
- The first 2 km has four crossings and 14 direction changes, where a cross-country line would typically have two or three.
- The line must run parallel to, and tie into, an existing pipeline. At the launcher end, a live tank farm and building footprint had to be cleared.
- Route optimisation focused on placing crossings and turns where they could be built, not on shortening the line.
- Material grade was a real choice. At 43 barg, API 5L Gr. B is viable, with a lower carbon equivalent, a wider supply base and simpler weldability qualification, but it has much less margin than X52 under the same design conditions. The two governing checks were combined biaxial stress in the restrained buried line and effective stress under highway loading at crossings.
- The buried line and the above-ground pig-trap stations follow different codes, stress formulations and allowable bases, yet are physically continuous. The battery limit could not be treated as a fixed boundary, so the movements and thrust at the transitions had to come out of the analysis as results.
Our approach
- Grade comparison. The full wall thickness and stress calculation set was run for both X52 and Gr. B at both design factors, through to bend thinning and hot-bend mother-pipe selection. The aim was to show where each grade gets tight and give the client a decision-level comparison.
- Crossing design basis. API RP 1102: fully corroded wall, 1.5 m cover, standard tandem-axle load of 44.5 kN per wheel over a 0.093 m² contact area, an impact factor of 1.5, and both flexible-pavement and no-pavement cases.
- Crossing methods. Three crossings were open cut at 90° where the road could be broken. The fourth, on the main approach road, was a 79 m horizontal directional drill (HDD) at 75° skew, to avoid opening the road.
- Route selection. Finalised against the grade decision. The minimum elastic bend radius differs by a factor of two between the grades, so intersection points, turn angles and hot-bend positions were set for the adopted grade.
- Deliverables. Alignment sheets, station approach drawings, trench section, crossing matrix and marker details, issued as one coordinated set.
- Stress analysis. One continuous CAESAR II model of about 1,255 nodes covering launcher, pipeline and receiver, with ASME B31.4 for buried restrained lengths and ASME B31.3 for above-ground station piping. Burial was modelled with soil density of 1,800 kg/m³ and a 33° friction angle, and friction coefficients of 0.50 (steel on soil) and 0.30 (steel on steel). 18 load cases: hydrotest, maximum and minimum operating, four operating seismic cases (0.2 g static, both horizontal axes, both signs), matched alternative sustained cases, two sustained cases and three expansion ranges, including the maximum-to-minimum thermal differential.
The outcome
- Grade choice. Both grades passed every check, for both flexible-pavement and no-pavement crossings, with no increase in cover and no casing or protection slab. The client selected Gr. B on the published margins.
- Consequences of Gr. B. A minimum elastic bend radius of 2000D, versus 1000D for X52, and a hot-bend mother pipe of 12.7 mm, versus 9.53 mm for X52.
- Adopted alignment. 11.13 mm wall along the route, stepping to 12.7 mm through the crossings. Four crossings across about 2,075 m (three open cut and one 79 m HDD), with 1.0–1.2 m cover and 1.5 m at crossings.
- Stress analysis. All 18 load cases passed, with zero code violations. The governing condition was the alternative sustained case at 97.3% of allowable in the above-ground station piping (B31.3). Sustained reached 88.6%, operating (including all four seismic cases) 63.8%, expansion 49.5% and hydrotest 48.1%.
- No anchor blocks. Soil restraint and the pig-trap arrangement absorbed the thermal and seismic loads, which removed that civil scope from the design.
| Parameter | X52 | Gr. B |
|---|---|---|
| Wall thickness | 9.53 mm | 11.13 mm |
| Hoop stress | 155.3 MPa | 124.0 MPa |
| Combined biaxial stress | 272.9 MPa (allowable 324 MPa) | 209.9 MPa (allowable 216.9 MPa) |
| Utilisation | 84% | 97% |
| Highway effective stress | 209.5 MPa (allowable 324 MPa) | 192.5 MPa (allowable 216.9 MPa) |
Codes, standards and tools
- ASME B31.4 (2016)
- ASME B31.3
- ASME B36.10M
- API 5L (46th Edition)
- API RP 1102 (7th Edition)
- PD 8010-1:2004
- NACE MR0175 / MR0103
- CAESAR II
- AutoCAD Civil 3D
- AutoCAD Plant 3D