← All projects

Firefighting · 2025

Buried GRE Firewater Network — Gas Treatment Plant, Egypt

International EPC contractor, for a major operator's gas treatment plant

Project overview

Project details

Client
International EPC contractor, for a major operator's gas treatment plant
Year
2025
Category
Firefighting
Location
Egypt
  • ISO 14692
  • ASME B31.3
  • GRE
  • CAESAR II
  • Buried Piping
  • Seismic Analysis
  • Thrust Blocks
  • Laminate Reinforcement

ISO 14692 stress analysis of a plant-wide buried glass-reinforced epoxy (GRE) firewater network for a new onshore gas treatment plant. It covers 174 lines from 2 to 18 inches, solved in one CAESAR II model, with local laminate reinforcement issued for construction.

  • 174lines in one model
  • 94.8%governing utilisation
  • 153reinforcement entries

The challenge

  • GRE cannot be qualified by analogy with steel. The laminate is strongly anisotropic: short-term hoop strength is about 250 MPa, short-term axial strength is 65 MPa, and the axial tensile modulus is roughly half the hoop value.
  • A buried, fully restrained pipe under internal pressure and a 54 °C installation-to-operating temperature swing places its main demand on the weak axial direction.
  • The coefficient of thermal expansion is 20 × 10⁻⁶/°C, higher than carbon steel, so the restrained thermal load is larger while the available modulus is smaller.
  • The joints add complexity. The system is adhesive-bonded taper-bell, not welded, and tees and elbows are moulded or filament-wound components, each with its own qualified envelope that a stress intensification factor does not cover.
  • Qualification must use the ISO 14692 biaxial envelope at each component, at design life and temperature, with part factors applied. That differs from a B31.3 code stress ratio.
  • The network was analysed as one system: 174 lines from 2 to 18 inches, buried 0.5 to nearly 4 metres deep. On a closed ring main, splitting it into sub-models would change the result.

Our approach

  • Built as a single CAESAR II V13 model and solved in one run.
  • Each line used a soil model matching its actual cover. Fourteen soil models were defined in 250 mm depth bands from 500 mm to 3,750 mm.
  • Material data came from the manufacturer's laminate data, entered as a full orthotropic definition: hoop and axial tensile and bending moduli, shear modulus, volumetric modulus and both Poisson ratios.
  • The long-term envelope used qualified stresses at five biaxial ratios: 0:1, 1:1, 2:1, 1:0 and 0:−1. ISO 14692 part factors were applied by load category, with a 0.85 fluid thermal derating factor.
  • A 21-case load matrix separated two operating thermal states, resolved expansion as three pairwise combinations, and applied 0.2 g seismic in four horizontal directions, both alone and superimposed on sustained loads. Wind was excluded, since the system is fully buried.
  • Local fixes were used where the envelope was exceeded: 18-inch tee bodies increased from 15.4 mm to 23 mm, 500 mm of pipe on each side of those tees from 10.1 mm to 17.7 mm, and 18-inch elbows from 12.4 mm to 18.4 mm, with equivalent local increases at 8, 6, 4 and 2 inches.
  • Each increase was recorded in a numbered schedule and marked on the isometric.

The outcome

  • With local reinforcement, the network passed all 21 load cases with no code violations.
  • Governing utilisation was 94.8% on the operating case at maximum design temperature (42.1 MPa against a 44.4 MPa allowable). Hydrotest reached 76.9%, sustained 69.6%, the second operating thermal state 87.7% and seismic plus sustained (occasional) 54.6%.
  • The four operating-plus-seismic cases matched the operating case ratio exactly. The thermal and pressure state governed, not seismic inertia, so the seismic scope was closed.
  • Two thrust blocks for the entire plant, both on 18-inch headers, with maximum design loads of 246 kN and 235 kN. A thrust block from an earlier revision was deleted after depth-specific soil restraint showed sufficient friction. Elsewhere, soil friction resists pressure thrust.
  • Deliverables: 153 local reinforcement entries across 80 marked-up isometrics. Each entry lists component type, size, original, added and final thickness, and location.
  • No pressure class change, re-routing or added anchor blocks were needed, and most of the network was built at catalogue thickness. Issued for construction at Rev. 02.

Codes, standards and tools

  • ISO 14692-2017
  • ASME B31.3
  • ASTM D2310
  • ASTM D3567
  • ASTM D1599
  • ASTM D4024
  • ASME B16.5
  • API 609
  • CAESAR II V13 Basic Soil Model

Discuss a similar project.

Get a quote